ACM Home Page
Please provide us with feedback. Feedback
Propagation delay fault: a new fault model to test delay faults
Full text PdfPdf (95 KB)
Source Asia and South Pacific Design Automation Conference archive
Proceedings of the 2005 Asia and South Pacific Design Automation Conference table of contents
Shanghai, China
SESSION: Test and DFT (2) table of contents
Pages: 178 - 183  
Year of Publication: 2005
ISBN:0-7803-8737-6
Authors
Xijiang Lin  Mentor Graphics Corp., Wilsonville, OR
Janusz Rajski  Mentor Graphics Corp., Wilsonville, OR
Sponsors
SIGDA: ACM Special Interest Group on Design Automation
: Shanghai IC Industry Association
: IEEE SSCS Shanghai Chapter
: IEEE CAS
: IEEE Beijing Section
: Fudan University
: Chinese Institute of Electronics
Publisher
ACM  New York, NY, USA
Bibliometrics
Downloads (6 Weeks): 2,   Downloads (12 Months): 14,   Citation Count: 1
Additional Information:

abstract   references   cited by   collaborative colleagues  

Tools and Actions: Review this Article  
DOI Bookmark: Use this link to bookmark this Article: http://doi.acm.org/10.1145/1120725.1120799
What is a DOI?

ABSTRACT

A new fault model, named propagation delay fault model, is proposed to test the gross gate delay defects modeled at each gate terminal and the distributed delay defects in the fault propagation paths. The proposed fault model assumes that the sum of the gross gate delay defect and the distributed delay defect are large enough to cause timing violation for all the paths passing through the fault site and the fault propagation path. Experimental results demonstrate that high fault coverage can be achieved in a reasonable amount of time and the test set size is comparable to the test set size generated for the transition fault model.


REFERENCES

Note: OCR errors may be found in this Reference List extracted from the full text article. ACM has opted to expose the complete List rather than only correct and linked references.

 
1
J. A. Waicukauski, E. Lindbloom, B. K. Rosen, and V. S. Iyengar, "Transition Fault Simulation," in IEEE Design & Test of Computer, pp. 32--38, Apr. 1987.
 
2
V. S. Iyengar, B. K. Rosen, and J. A. Waicukauski, "On Computing the Sizes of Detected Delay Faults," in IEEE Trans. on CAD, Vol. 9, No. 3, pp.299--312, Mar. 1990.
 
3
 
4
K.-T. Cheng, "Transition Fault Testing for Sequential Circuits," IEEE Trans. on CAD, Vol. 12, No. 12, pp. 1971--1983, 1993.
 
5
J. Savir and S. Patil, "Broad-Side Delay Test," in IEEE Trans. on CAD, Vol. 13, No. 8, pp. 1232--1241, Aug. 1994.
 
6
 
7
J. L. Carter, V. S. Iyengar, and B. K. Rosen, "Efficient Test Coverage Determination for Delay Faults," in Proc. Intl. Test Conf., pp. 418--427, Sept. 1987.
 
8
G. L. Smith, "Model for Delay Faults Based upon Paths," in Proc. Intl. test conf., pp. 342--349, Sept. 1985.
 
9
C. J. Lin and S. M. Reddy, "On Delay Testing in Logic Circuits," in IEEE Trans. on CAD, pp. 694--703, Sept. 1987.
 
10
K. Fuchs, M. Pabst, and T. Rossel, "RESIST: A Recursive Test Pattern Generation Algorithm for Path Delay Faults Considering Various Test Classes," in IEEE Trans. on CAD, Vol. 13, pp.1550--1562, Dec. 1994.
 
11
 
12
M. H. Schulz, F. Fink, and K. Fuchs, "Parallel Pattern Fault Simulation for Path Delay Faults," in Proc. 19th Fault Tolerant Comp. Symp., pp 44--51, Jul. 1989.
 
13
K.-T. Cheng and H.-C. Chen, "Classification and Identification of Nonrobust Untestable Path Delay Faults," in IEEE Trans. on CAD, Vol. 15, No. 8, pp. 845--853, Aug. 1996.
 
14
 
15
E. S. Park and M. R. Mercer, "An Efficient Delay Test Generation System for Combinational Logic circuits," in IEEE Trans. on CAD, Vol 11, pp. 926--938, Jul. 1992.
 
16
 
17
 
18
W. Qiu and D. M. H. Walker, "an Efficient Algorithm for Finding the K Longest Testable Paths Through Each Gate in a Combinational Circuit." Intl. Test Conf., pp.592--601, 2003.
 
19
 
20

Collaborative Colleagues:
Xijiang Lin: colleagues
Janusz Rajski: colleagues